When you open Amperes 4, the first number you see is charging current — displayed in milliamps (mA). It is the most direct measurement of how fast your battery is filling up. Here is what that number means, why it changes, and how to use it intelligently.
What Is mA (Milliamps)?
Milliamps (mA) measure electrical current — the rate of electron flow through a circuit. For battery charging, mA represents how quickly charge is flowing into (positive values) or out of (negative values) the battery. 1,000mA equals 1 Ampere. A charging session at 2,000mA fills your battery twice as fast as one at 1,000mA, all else being equal.
The Relationship Between Current, Voltage, and Charging Power
Power (watts) = current (amps) × voltage (volts). This means two chargers can deliver the same wattage in different ways: 5V at 3A = 15W, and 9V at 1.67A = 15W. Amperes 4 shows current (mA), but some screens also show voltage. For a complete picture of charging power, multiply the two values. This is why a fast-charge session at 9V and 2,000mA is delivering significantly more power than a 5V/2,000mA standard session.
Normal mA Ranges for Different iPhone Models
- iPhone 6s / 7 with 5W charger: 700–900mA (max ~4.5W)
- iPhone 8 / X with 5W charger: 800–1,000mA
- iPhone 8 / X with 18W USB-C charger (fast charge): 1,800–2,500mA
- iPhone 12–14 with 20W USB-C charger (fast charge): 1,800–2,800mA
- iPhone 15 Pro with 30W USB-C charger (fast charge): 2,200–3,000mA
- Any iPhone on a computer USB 2.0 port: 300–500mA
Why Charging Current Changes Throughout a Session
mA readings are not constant — they change based on battery level, temperature, and system activity. A typical charging session shows three phases:
- 1Pre-conditioning (0–20%): Current may be lower while iOS warms the battery gently from deep discharge, or accelerated as the system quickly fills a very empty cell.
- 2Constant current phase (20–80%): This is when you see peak mA readings. The charging controller delivers maximum current, and this is the most informative reading for comparing cables and chargers.
- 3Taper phase (80–100%): Current gradually reduces to protect the battery cell. By 95%, you may be seeing only 200–400mA regardless of charger quality.
What Does a Negative mA Reading Mean?
A negative mA reading — for example, -300mA — means your iPhone is consuming more power than the charger is delivering. The battery is net discharging even though a charger is connected. This happens when the screen is on, the processor is busy with demanding tasks, and the charging input is from a weak source (like a computer USB port or a low-wattage charger). Switch to a higher-wattage adapter or turn off the screen to bring the reading positive.
Reading the Amperes 4 Dashboard
- Measured charging current in mA: The result shown after a completed test. Positive = net charging, negative = net discharging. Note: the preliminary reading displayed at test start is highly inaccurate on iOS 17 and later due to Apple's restrictions on battery data reporting frequency.
- Percentage estimate: Amperes 4 shows estimated percentage per hour based on current mA and your battery capacity setting.
- Chart view: Shows how current has varied over your charging session — useful for identifying charger behavior.
- Session log: Historical saved tests let you compare performance across different accessories over time.
On iOS 17 and later, a complete and accurate mA result requires a full test of up to 30 minutes. The preliminary reading shown at the start is highly inaccurate — do not use it for cable or charger comparisons. Always wait for the test to finish, then compare final results from sessions run under the same conditions: battery at 20–80%, phone idle and screen off, same charger and cable each time.